Direct Outdoor Thermal Enclosures · NEMA 250 / IEC 60529 IP55–IP65 · 15-Minute Formal Quote
SECTION Engineering CalculatorUPDATED 2026-11-22REVIEWED Jack Lau, Thermal Systems Lead

Outdoor Enclosure Solar Heat Load & AC Sizing Calculator (Watts & BTU/hr)

Calculate internal IT heat load, double-wall solar heat gain, and ambient delta-T conduction in Watts and BTU/hr to size 300W–4000W outdoor enclosure AC units.

INTERACTIVE ENGINEERING CALCULATOR

Outdoor Enclosure Solar & IT Heat Load Calculator

Estimate total thermal load (internal IT Watts + double-wall solar gain + ambient delta-T conduction) to select the right 300W–4000W closed-loop air conditioner.

Required Cooling Capacity (Watts)1,571 W
Required Cooling Capacity (BTU/hr)5,360 BTU/hr
Recommended ONE SeriesOD-32U-AC2000 (2000W AC)
Send Sizing to Engineering (15-Min Quote)Model assumes double-wall RAL 7035 solar-shielded envelope (~65 W/m² net solar gain) plus 1.8 W/(m²·K) conductive gain. Verify final sizing with our engineering desk.

Use the interactive calculator above to estimate total cooling capacity in Watts and BTU/hr for a double-wall, RAL 7035 solar-shielded outdoor network cabinet. Accurate thermal sizing prevents two costly field failures: undersized compressors that run continuously at 100% duty cycle until switches throttle, and grossly oversized units that short-cycle and fail to dehumidify internal air properly.

Double-wall solar shield vs single-wall heat balance diagram

The Three Components of Outdoor Enclosure Heat Load

Total required cooling capacity (Q_total) is the sum of internal electrical dissipation, net solar radiation passing through the cabinet shell, and conductive heat transfer whenever outdoor ambient temperature exceeds your target internal rack temperature:

  1. Internal IT & Power Conversion Heat (Q_IT): Sum the actual continuous power draw (Watts) of switches, routers, OLTs, edge servers, and PoE injectors—plus rectifier/UPS conversion losses (typically 8–12% of DC load). Multiply Watts by 3.41214 to convert to BTU/hr.
  2. Net Double-Wall Solar Heat Gain (Q_solar): Direct midday sun delivers roughly 900–1,000 W/m² onto exposed metal. A double-wall RAL 7035 solar-shielded envelope with a 25 mm ventilated air gap and 15–20 mm PEF liner cuts net inward solar transfer to approximately 65 W/m² of exposed surface area. Learn the underlying physics in our Double-Wall Solar Heat Gain Guide.
  3. Conductive Ambient Delta-T Gain (Q_cond): Whenever peak outdoor air (T_amb) is warmer than target internal temperature (T_int, typically +30 °C to +35 °C), heat conducts inward at roughly 1.8 W/(m²·K) across an insulated double-wall chassis.

Typical Exposed Surface Area by OD-Series Cabinet

Enter the surface area corresponding to your target rack size into the calculator above:

Model Code External Dimensions (H × W × D) Exposed Surface Area (5 Faces) Built-In Cooling Capacity
OD-12U-AC300 750 × 650 × 650 mm (29.5 × 25.6 × 25.6 in) ~2.3 m² 300 W (1,024 BTU/hr)
OD-24U-AC600 1400 × 750 × 750 mm (55.1 × 29.5 × 29.5 in) ~4.2 m² 600 W (2,047 BTU/hr)
OD-32U-AC2000 1850 × 800 × 900 mm (72.8 × 31.5 × 35.4 in) ~6.4 m² 2,000 W (6,824 BTU/hr)
OD-42U-AC4000 2250 × 800 × 1100 mm (88.6 × 31.5 × 43.3 in) ~8.8 m² 4,000 W (13,648 BTU/hr)

Closed-loop dual-circuit airflow schematic showing evaporator and condenser thermal loops

Next Steps: Voltage Selection & Project Thermal Verification

Once you have your estimated cooling wattage, verify compressor voltage, circuit breaker ampacity, and winter heater sizing in our 110V vs. 220V Enclosure AC Sizing Guide. Every OD-Series cabinet is built to NEMA 250 / IEC 60529 IP55–IP65 outdoor thermal enclosure and EIA-310-E 19-inch mounting standards; thermal test sheets available per project.

Need an engineer to double-check altitude derating, battery heat dissipation, or dual-AC redundancy? Click Send Sizing to Engineering above or open our 15-Minute Formal Quote Brief.

MATCHING CONFIGURATIONS

Standard & Custom-Engineered Models

View All 5 Models →
OD-12U-AC300

12U Pole/Pad Mount + 300W Micro-AC

Compact 12U double-wall solar-shielded cabinet pairing a 300W (1,024 BTU/hr) closed-loop compressor AC with heavy-duty pole/wall/pad brackets for WISP relays and campus fiber nodes.

Full Datasheet →
OD-24U-AC600

24U Double-Wall + 600W AC

Balanced 24U pad-mount double-wall cabinet combining a 600W (2,047 BTU/hr) closed-loop air conditioner with a segregated lower 48V battery bay for WISP distribution hubs and roadside ITS.

Full Datasheet →
OD-32U-AC2000

Flagship 32U Double-Wall + 2000W Industrial AC

Flagship 32U double-wall solar-shielded enclosure pairing a high-ambient 2000W (6,824 BTU/hr) closed-loop industrial AC with full-depth 19-inch rails for dense ITS, solar-BESS, and mining edge compute.

Full Datasheet →